Blog

How to troubleshoot common problems in Swep Heat Exchanger?

Sep 03, 2025Leave a message

Hey there! As a supplier of Swep Heat Exchangers, I've seen my fair share of issues pop up with these things. Today, I'm gonna walk you through how to troubleshoot some common problems you might run into with your Swep Heat Exchanger.

1. Low Heat Transfer Efficiency

One of the most common issues is a drop in heat transfer efficiency. You might notice that your system isn't heating or cooling as effectively as it used to. There are a few reasons this could be happening.

Fouling

Fouling is a major culprit. Over time, dirt, scale, and other debris can build up on the heat exchanger plates. This acts as an insulator, reducing the amount of heat that can be transferred between the fluids. To check for fouling, you can take a look at the pressure drop across the heat exchanger. If it's higher than normal, fouling could be the cause.

The solution? Cleaning the heat exchanger. You can use a chemical cleaner that's specifically designed for heat exchangers. Make sure to follow the manufacturer's instructions carefully. If the fouling is really bad, you might need to disassemble the heat exchanger and clean the plates manually.

Incorrect Flow Rates

Another reason for low heat transfer efficiency could be incorrect flow rates. If the flow rate of either the hot or cold fluid is too low, there won't be enough contact between the fluids to transfer heat effectively. You can check the flow rates using flow meters. If the flow rates are off, you'll need to adjust the pumps or valves to get them back to the correct levels.

2. Leakage

Leakage is another problem that can occur with Swep Heat Exchangers. You might notice fluid dripping from the heat exchanger or a decrease in the fluid levels in your system.

Gasket Failure

If you have a gasketed heat exchanger, gasket failure is a common cause of leakage. Gaskets can wear out over time, especially if they're exposed to high temperatures or harsh chemicals. To check for gasket failure, you can look for signs of gasket damage, such as cracks or tears.

If you find a damaged gasket, you'll need to replace it. Make sure to use a gasket that's compatible with your heat exchanger and the fluids it's handling. You can find replacement gaskets from the manufacturer or from a reputable supplier.

Brazing Defects

For Nickel Brazed Plate Heat Exchanger and Aluminum Brazed Heat Exchanger, brazing defects can cause leakage. Brazing is the process of joining the plates together using a filler metal. If the brazing isn't done correctly, there could be small holes or cracks in the joints.

To detect brazing defects, you can use a pressure test. If the heat exchanger fails the pressure test, it likely has a brazing defect. Unfortunately, if you have a brazing defect, the heat exchanger might need to be replaced, as it can be difficult to repair brazing defects.

3. High Pressure Drop

A high pressure drop across the heat exchanger can also be a problem. It can cause the pumps to work harder, which can lead to increased energy consumption and premature pump failure.

Blockages

Blockages in the heat exchanger can cause a high pressure drop. This could be due to fouling, as mentioned earlier, or it could be caused by debris that's gotten into the system. To check for blockages, you can take a look at the pressure drop across the heat exchanger and compare it to the normal values.

If you suspect a blockage, you'll need to clean the heat exchanger to remove the debris. You might also need to check the filters in your system to make sure they're working properly and not allowing debris to pass through.

Incorrect Pipe Sizing

Incorrect pipe sizing can also lead to a high pressure drop. If the pipes are too small, the fluid will have to flow through a smaller area, which can increase the pressure drop. You can check the pipe sizing by referring to the system design specifications. If the pipe sizing is incorrect, you'll need to replace the pipes with ones that are the correct size.

4. Vibration and Noise

Vibration and noise can be annoying and can also indicate a problem with the heat exchanger.

Loose Components

Loose components can cause vibration and noise. Check to make sure all the bolts and nuts on the heat exchanger are tightened properly. You can also check for any loose pipes or fittings that might be causing the vibration.

If you find any loose components, simply tighten them up. Make sure not to over-tighten, as this can cause damage to the components.

Cavitation

Cavitation can also cause vibration and noise. Cavitation occurs when the pressure of the fluid drops below its vapor pressure, causing bubbles to form. When these bubbles collapse, they can create a lot of noise and vibration.

To prevent cavitation, you need to make sure the flow rates and pressures in the system are within the recommended range. You can also check the pump impellers for signs of cavitation damage. If you find cavitation damage, you'll need to replace the impellers.

5. Corrosion

Corrosion is a long-term problem that can affect the performance and lifespan of your Swep Heat Exchanger.

Chemical Attack

If the fluids in your system are corrosive, they can attack the materials of the heat exchanger. This can lead to thinning of the plates, holes, and ultimately, failure of the heat exchanger.

To prevent chemical attack, you need to choose the right materials for your heat exchanger. Swep offers a variety of materials that are resistant to different types of chemicals. You can also use corrosion inhibitors in the fluids to reduce the rate of corrosion.

Galvanic Corrosion

Galvanic corrosion can occur when two different metals are in contact with each other in the presence of an electrolyte. This can happen if you have a heat exchanger that's made of different metals or if there are different metals in the piping system.

Brazed Plate Type Heat ExchangerNickel Brazed Plate Heat Exchanger

To prevent galvanic corrosion, you can use insulating gaskets or coatings to separate the different metals. You can also make sure that the metals in your system are compatible with each other.

Conclusion

Well, there you have it! These are some of the most common problems you might run into with Swep Heat Exchangers and how to troubleshoot them. If you're still having issues after trying these troubleshooting steps, don't hesitate to reach out. As a supplier, we have a team of experts who can help you diagnose and solve any problems you might be having with your Brazed Plate Type Heat Exchanger or other Swep products. Whether you're looking to purchase a new heat exchanger or need help with an existing one, we're here to assist you every step of the way.

References

  • Swep Heat Exchanger Manufacturer's Manual
  • Heat Exchanger Maintenance and Troubleshooting Guides
Send Inquiry